sighting issue

Ask about your Model 8 & 81
Post Reply
60DRB
Posts: 3
Joined: Sun Nov 27, 2016 9:39 am

sighting issue

Post by 60DRB » Sat Dec 08, 2018 5:43 am

I'm trying to get my 1927 in .30 Rem. to settle...

-Rear sight is the Marble's R6 and the front is a Lyman 5B folding sight.
-Using my reloads with new brass (30-30 loading info), seems to operate fine. Bullet impacts are scattered, about 12' pattern at 100 yards.

1st. The front sight is loose in the dovetail. What is the best way to tighten this? Also, what is the purpose/usage for the post/bead versus the post/ring on this?
2nd. Not that familiar with the tang peep sight. The elevation adjustment seems simple enough... How is windage adjustment accomplished?

kenhwind
Posts: 164
Joined: Tue Jun 23, 2009 6:50 am

Re: sighting issue

Post by kenhwind » Sat Dec 08, 2018 12:06 pm

There is a couple of ways to seat the front sight:
One is with Locktite, but then you cannot move it.
The other it to dimple the bottom of the front sight with a center punch.
If someone drove the sight out to the left it mau have opened up the dovetail cut in the sight base.

When using an aperture type sight, either a tang sight or receiver sight, you center the front sight bead in the aperture. In this cse I assume you'd line up both sights.
Windage is adjustable using the front sight.
KEN

Kootenay52
Posts: 8
Joined: Tue Dec 04, 2018 6:34 pm

Re: sighting issue

Post by Kootenay52 » Sat Dec 08, 2018 8:11 pm

I have taken the front sight out and put a very thin piece of plastic (like paper thin) under the dovetail of the front sight and then reinstalled the front sight. This has worked well for me in the past. Laminate plastic material comes in different thicknesses. I simply found a thickness that was enough to tighten things up.
Cheers, Bill.

60DRB
Posts: 3
Joined: Sun Nov 27, 2016 9:39 am

Re: sighting issue

Post by 60DRB » Sun Dec 09, 2018 7:36 am

...dove tail opened up. Yes, that is the situation. While trying to adjust L/R at 100 yards the front sight came right out, the left side. I'll try shimming. I've heard foil might also work for shim material. We shall see.

What exactly is the purpose of the ring versus open post front sight?

It would be nice if the tang sight could be adjusted for windage. Some peep sights are made to do that.

User avatar
Phyrbird
Posts: 817
Joined: Mon Jan 07, 2013 10:53 pm

Re: sighting issue

Post by Phyrbird » Sun Dec 09, 2018 12:19 pm

I agree @ the plastic, just not the source. Many machine tool suppliers can sell plastic shim stock in various thicknesses down to about .002. It's Great & it is very stable for these applications....
Try it, comes in 8 1/2 x 11 sheets, affordable too...
Phyrbird
SOKY

Kootenay52
Posts: 8
Joined: Tue Dec 04, 2018 6:34 pm

Re: sighting issue

Post by Kootenay52 » Sun Dec 09, 2018 6:13 pm

Phyrbird wrote:
Sun Dec 09, 2018 12:19 pm
I agree @ the plastic, just not the source. Many machine tool suppliers can sell plastic shim stock in various thicknesses down to about .002. It's Great & it is very stable for these applications....
Try it, comes in 8 1/2 x 11 sheets, affordable too...
Sounds good ....I will give that a try next time

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest