Scout mount

Talk about things other than the Model 8's and 81's
Post Reply
jim18611865
Posts: 100
Joined: Thu May 15, 2014 9:16 pm

Scout mount

Post by jim18611865 »

Fellow member "Fred" here made this for me to try.
I think it is going to work.
Got the laser bore sighter out and tweaked it right in.
I may undo everything and bed it in as suggested.
Angle is weird but the scope is just forward of the ejection port.
81 mount_1.jpg
81 mount_1.jpg (131.52 KiB) Viewed 650 times
81 Mount _2.jpg
81 Mount _2.jpg (134.71 KiB) Viewed 650 times

User avatar
81police
Posts: 2383
Joined: Thu Feb 05, 2009 12:12 pm
Location: TEXAS

Re: Scout mount

Post by 81police »

Would love to hear how it shoots!
Cam Woodall
Site Co-Administrator

jim18611865
Posts: 100
Joined: Thu May 15, 2014 9:16 pm

Re: Scout mount

Post by jim18611865 »

Target # 1 50 Yards
First three shots at the bottom before the scope was dialed in aiming at the center. Nice close group though.
.93"
The lone hole is me walking the scope up.
Three in the center 1.68"
Four up top 1.805"
scoped 81 _ 1.jpg
scoped 81 _ 1.jpg (125.28 KiB) Viewed 611 times

jim18611865
Posts: 100
Joined: Thu May 15, 2014 9:16 pm

Re: Scout mount

Post by jim18611865 »

Target #2 again 50 Yards.
Middle group 2.43"
Top group and actually the last fired 3.18"
Attachments
scoped 81 _ 2.jpg
scoped 81 _ 2.jpg (120.32 KiB) Viewed 611 times

jim18611865
Posts: 100
Joined: Thu May 15, 2014 9:16 pm

Re: Scout mount

Post by jim18611865 »

Target # 3 at 50 yards trying my hardest.
1.43"
Without that flyer it would have been .68".
I figure 4 is the right group size as that is all my magazine will hold. I don't know why.
scoped 81 _ 3.jpg
scoped 81 _ 3.jpg (121.01 KiB) Viewed 611 times
I then went directly to the 200 yards plates and missed 12 times at a 12"W X 18"H plate. I may revisit that later after seeing what 100 yards looks like.
I don't think the mount came loose at all.
I shot around 34 rounds total.
Man my shoulder hurts.

Jim

Fred
Posts: 133
Joined: Wed Feb 26, 2014 11:10 pm

Re: Scout mount

Post by Fred »

jim18611865 wrote:
Sun Aug 16, 2020 4:57 pm
I shot around 34 rounds total.
Man my shoulder hurts.
Must have been shooting off a bench. :D Your 81 shoots better than mine for sure. What load are you using?

Thanks for sharing your range report.

jim18611865
Posts: 100
Joined: Thu May 15, 2014 9:16 pm

Re: Scout mount

Post by jim18611865 »

Yes, off a bench, but next time I will be using a Lead Sled.

All the bullets were Speer 170s.
All primers were WLRs.
Some had 31.5 gns. of 3031, the GRUMPA cases had 31.8 gns.
COAL of 2.53.
Mixed cases, but some (18 of them) were new made by GRUMPA that I bought over a year ago. None of his cases had backed out primers so I must be resizing too much. Now I know how much to resize and where to set the shoulder. I had a couple that needed a bump to close the bolt. I must have been very close to the perfect reload for this gun. Whether the the bullet was close or the shoulder, I do not know.

Jim

User avatar
Bandersnatch
Posts: 428
Joined: Tue Oct 21, 2014 3:48 am
Location: Lower Alabama

Re: Scout mount

Post by Bandersnatch »

What caliber?
I am the cat who walks by himself. And all places are alike to me.

jim18611865
Posts: 100
Joined: Thu May 15, 2014 9:16 pm

Re: Scout mount

Post by jim18611865 »

Sorry I should have mentioned that, it is a .32.

Jim

User avatar
Bandersnatch
Posts: 428
Joined: Tue Oct 21, 2014 3:48 am
Location: Lower Alabama

Re: Scout mount

Post by Bandersnatch »

jim18611865 wrote:
Wed Aug 19, 2020 5:00 am
Sorry I should have mentioned that, it is a .32.

Jim
Very good. The holes seemed a trifle large for a .30.

I have sometimes considered a mount like this but I've been leery of putting so much weight on those two screws.
I am the cat who walks by himself. And all places are alike to me.

jim18611865
Posts: 100
Joined: Thu May 15, 2014 9:16 pm

Re: Scout mount

Post by jim18611865 »

Well, someone had to be the crash test dummy. "Fred" suggested I bed it with epoxy, which I did.
Time will tell.
I'll take it out in a few weeks and put a bunch more through it and see how it goes. (Need lead sled, says my shoulder)

"Fred" made it so the posts that are the threaded holes actually go up into the mount. It was an excellent job and the curve he put on the bottom of that mount was a perfect fit to the barrel jacket. The pressure isn't on the actual screws, but the posts themselves, if that makes sense. The rear sight didn't come with the rifle.

Jim

Fred
Posts: 133
Joined: Wed Feb 26, 2014 11:10 pm

Re: Scout mount

Post by Fred »

For a range gun shooting cartridges of moderate performance in an 9lb rifle I think those 2 screws will do alright. I probably wouldn't trust them for a rugged high dollar hunt without extensive testing to ensure they're up to the task.

I'm confident the screws themselves will hold up, but the narrow spacing might not do it any favors. It'd be interesting to settle on an accurate load, zero the rifle and bump one end of the scope with a towel-wrapped lump of wood from the side, and see just how sensitive to rough handling it is. Side-loading the ocular or the objective will torque the assembly the most. If it holds zero, then you'd have greater confidence about it surviving in the wild.

User avatar
Bandersnatch
Posts: 428
Joined: Tue Oct 21, 2014 3:48 am
Location: Lower Alabama

Re: Scout mount

Post by Bandersnatch »

Any more news on this mount? I'm beginning to get ideas....
I am the cat who walks by himself. And all places are alike to me.

Post Reply